• If you are having problems logging in please use the Contact Us in the lower right hand corner of the forum page for assistance.

Trailer ?

Big Muddy rancher

Well-known member
The light on my brake controller will not light up. It is supposed to when the trailer plug is connected. I seem to have power on two prongs on the truck side of the plug. Is the brake feed different then the brake light feed?

Denny :?

Anybody :? :?
 

Denny

Well-known member
The light will not light up unless you have a complete connection to the brakes. I'd start with the plugs on the truck and trailer. First use a test light on the truck if the light on the brake control lights up your good back to there. If thats the case I'd take apart the plug for the trailer and see if the wire came loose. If that checks out start looking for a broken or corroded wire. Make sure the trailer is grounded good to the truck most trailers ground thru the ball and with the fold down and turn over balls rust will hinder your ground.To check for a good ground hook up a jumper wire from the trailer to the truck.
 

Big Muddy rancher

Well-known member
Thanks Denny, I have all my lights working and I can use a jumper wire to apply the brakes. It must be up the wire loom where it's not making connection(oh fun), I started peeling back up the line looking for the break.

Thanks again.
 

Big Muddy rancher

Well-known member
I wasn't worried about lights but brakes are a luxury i kinda enjoy. :shock:

Don't get me started Gcreek. My son borrowed the truck to tour some girls around and it came home plastered in mud and the trailer brakes wouldn't work when i hooked it back up. Not say but mighty suspicious. :?

Denny would their be a circuit breaker that could be bad on the brake line? I can't seem to find any problem with the wire.
 

Denny

Well-known member
I would check the brake feed wire where it goes into the plastic connector where the wire's branch out to the tail lights and plug. It's just under the bumper on the rear left corner.Those brake wires will corode going into the plug I just cut them and bypass the plug. It's best to soder the connections and put some heat shrink over the connections.If you don't they'll quit working some cold day in January.
 

gcreekrch

Well-known member
Big Muddy rancher said:
Don't get me started Gcreek. My son borrowed the truck to tour some girls around and it came home plastered in mud and the trailer brakes wouldn't work when i hooked it back up. Not say but mighty suspicious. :?

And you never did nothin' like that when you were young and in a hurry, hmmmm? :nod: :heart: :lol:
 

Big Muddy rancher

Well-known member
gcreekrch said:
Big Muddy rancher said:
Don't get me started Gcreek. My son borrowed the truck to tour some girls around and it came home plastered in mud and the trailer brakes wouldn't work when i hooked it back up. Not say but mighty suspicious. :?

And you never did nothin' like that when you were young and in a hurry, hmmmm? :nod: :heart: :lol:


Never :D
 

Big Muddy rancher

Well-known member
Denny said:
I would check the brake feed wire where it goes into the plastic connector where the wire's branch out to the tail lights and plug. It's just under the bumper on the rear left corner.Those brake wires will corode going into the plug I just cut them and bypass the plug. It's best to soder the connections and put some heat shrink over the connections.If you don't they'll quit working some cold day in January.


The wire seems fine It must be wired for trailers as it's not just splitter plug.
Still nothing but i have one place to check for more connections. Then I'm beat. :???:
 

RSL

Well-known member
gcreekrch said:
Big Muddy rancher said:
Don't get me started Gcreek. My son borrowed the truck to tour some girls around and it came home plastered in mud and the trailer brakes wouldn't work when i hooked it back up. Not say but mighty suspicious. :?

And you never did nothin' like that when you were young and in a hurry, hmmmm? :nod: :heart: :lol:

Hard to get muddy when its' parked... :twisted:
 

Denny

Well-known member
If you have current coming out of the brake controler it may be quicker just to run a new wire to the rear of the truck. I had to do that on a friend's dodge this spring it was 10 minutes with alot less headache.
 

Big Muddy rancher

Well-known member
Denny said:
If you have current coming out of the brake controler it may be quicker just to run a new wire to the rear of the truck. I had to do that on a friend's dodge this spring it was 10 minutes with alot less headache.

Do you remember which wire you connected to coming out of the controller?
This is a 97 Dodge W 250.
 

Denny

Well-known member
Blue wire is your trailer brake wire.

Black wire is the hot wire from the battery
red wire goes to the cold side of your stop light switch on the brake pedal

white wire is the gound.

If the truck has a factory tow package sometimes the colors don't match those coming out of the brake control.
 

per

Well-known member
I know from experience that if you get it wrong you can make white smoke come out of the brake controller. :cry:
 
Top